source: connect/other/pppoe.xml@ afa198d

<?xml version="1.0" encoding="ISO-8859-1"?>
<!DOCTYPE sect1 PUBLIC "-//OASIS//DTD DocBook XML V4.3//EN"
   "http://www.oasis-open.org/docbook/xml/4.3/docbookx.dtd" [
  <!ENTITY % general-entities SYSTEM "../../general.ent">
  %general-entities;
 
  <!ENTITY pppoe-download-http "http://www.roaringpenguin.com/products/rp-pppoe/rp-pppoe-&pppoe-version;.tar.gz">
  <!ENTITY pppoe-download-ftp  "ftp://ftp.rutgers.edu/pub/slackware/slackware_source/n/rp-pppoe/rp-pppoe-&pppoe-version;.tar.gz">
  <!ENTITY pppoe-size          "185 KB">
  <!ENTITY pppoe-buildsize     "2.2 MB">
  <!ENTITY pppoe-time          "0.05 SBU">
]>

<sect1 id="pppoe" xreflabel="RP-PPPoE-&pppoe-version;">
<?dbhtml filename="pppoe.html"?>
<title>RP-PPPoE-&pppoe-version;</title>

<sect2>
<title>Introduction to <application><acronym>RP</acronym>-<acronym>PPPoE</acronym></application></title>

<para>The Roaring Penguin <application><acronym>PPPoE</acronym></application> 
package contains both a client and a server component that works with the 
client. The client allows you to connect to large networks that use the 
<acronym>PPPoE</acronym> protocol, common among <acronym>ADSL</acronym> 
providers.  The server component runs alongside the client, 
allowing you to configure other clients that send out a configuration 
request.</para>

<sect3><title>Package information</title>
<itemizedlist spacing='compact'>
<listitem><para>Download (HTTP): <ulink
url="&pppoe-download-http;"/></para></listitem>
<listitem><para>Download (FTP): <ulink
url="&pppoe-download-ftp;"/></para></listitem>
<listitem><para>Download size: &pppoe-size;</para></listitem>
<listitem><para>Estimated Disk space required:
&pppoe-buildsize;</para></listitem>
<listitem><para>Estimated build time:
&pppoe-time;</para></listitem></itemizedlist>
</sect3>
                                                                                
<sect3><title><application><acronym>RP</acronym>-<acronym>PPPoE</acronym></application> dependencies</title>
<sect4><title>Required</title>
<para><xref linkend="ppp"/></para></sect4>
</sect3>


</sect2>

<sect2>
<title>Installation of <application><acronym>RP</acronym>-<acronym>PPPoE</acronym></application></title>

<para><emphasis>Note: </emphasis> If you plan on using kernel-mode PPPoE, 
this package is no longer explicitly needed.  However, it is recomended
for ease of configuration.   Additional information about kernel mode 
<acronym>PPPoE</acronym> can be found in 
<filename>rp-pppoe-&pppoe-version;/doc/KERNEL-MODE-PPPOE</filename>.</para>

<para>Install <application><acronym>RP</acronym>-<acronym>PPPoE</acronym></application> by running 
the following commands:</para>

<screen><userinput><command>cd src &amp;&amp;
./configure &amp;&amp;
make &amp;&amp;
make install</command></userinput></screen>

</sect2>

<sect2>
<title>Command explanations</title>

<para>These are the standard installation commands that will install into
the <filename>/usr</filename> prefix.  You can optionally use the 
<command>go</command> script in the root of the source tree, to
run the same commands, which are then immediately followed by the 
<command>adsl-setup</command> script.</para>

</sect2>

<sect2>
<title>Configuring <application><acronym>RP</acronym>-<acronym>PPPoE</acronym></application></title>

<sect3><title>Config files</title>
<para><filename>/etc/ppp/pppoe.conf</filename>, 
<filename>/etc/ppp/firewall-standalone</filename>, 
<filename>/etc/ppp/firewall-masq</filename>, 
<filename>/etc/ppp/pppoe-server-options</filename>, 
<filename>/etc/resolv.conf</filename>, 
<filename>/etc/ppp/pap-seecrets</filename>, 
<filename>/etc/ppp/chap-secrets</filename></para></sect3>

<sect3><title>Configuration Information</title>

<para>To configure <application><acronym>RP</acronym>-<acronym>PPPoE</acronym>
</application> after installation, you should run the <command>adsl-setup
</command> script.</para>

<para>When configuring your connection, you will need to have your 
<acronym>ISP</acronym>'s nameserver information available, as well as your 
username and password.  You will also be asked whether to configure a 
dial-on-demand or a constant connection.  If your service provider does not 
charge by the minute, it is usually good to have a bootscript handle the 
connection for you.  You can, of course, choose not to install the 
following script, and start your connection manually with the 
<command>adsl-start</command> script.</para>

<para><emphasis>Optionally</emphasis> install the 
<filename>/etc/sysconfig/network-devices/services/pppoe</filename> service 
script included with the <xref linkend="intro-important-bootscripts"/> 
package.</para>

<screen><userinput><command>make install-service-pppoe</command></userinput></screen>

<para>Now create the config file for use with the <filename>pppoe</filename> 
service script:</para>

<note>If you have previously configured the network interface that
will now
use <acronym>PPPoE</acronym>, you should remove the interface
configuration
files for that interface:
<command><userinput>rm /etc/sysconfig/network-devices/ifconfig.eth0/*</userinput></command>.</note>

<screen><userinput><command>install -d /etc/sysconfig/network-devices/ifconfig.eth0 &amp;&amp;
cat &gt; /etc/sysconfig/network-devices/ifconfig.eth0/pppoe &lt;&lt; "EOF"</command>
ONBOOT="yes"
SERVICE="pppoe"
<command>EOF</command></userinput></screen>

<!-- A TYPE="[user/kernel]" will be added at a later date when kernel
mode pppoe is described here. -->

</sect3>

</sect2>

<sect2>
<title>Contents</title>

<para>The <application><acronym>RP</acronym>-<acronym>PPPoE</acronym></application> package 
contains <command>adsl-setup</command>, <command>adsl-start</command>, 
<command>adsl-status</command>, <command>adsl-stop</command>, <command>
pppoe</command>, <command>pppoe-relay</command>, <command>pppoe-server
</command> and <command>pppoe-sniff</command>.</para>

</sect2>

<sect2><title>Description</title>

<sect3><title>adsl-setup</title>
<para>A script for configuring the client.  Configuration is then stored
in <filename>/etc/ppp/pppoe.conf</filename>.</para></sect3>

<sect3><title>adsl-start</title>
<para><command>adsl-start</command> starts the client using the options 
specified in <filename>/etc/ppp/pppoe.conf</filename>.</para></sect3>

<sect3><title>adsl-status</title>
<para><command>adsl-status</command> displays the status of the
<acronym>ADSL</acronym> connection.</para></sect3>

<sect3><title>adsl-stop</title>
<para><command>adsl-stop</command> stops the client.</para></sect3>

<sect3><title>pppoe</title>
<para>This is the client itself. Generally it should not be started on its 
own.</para></sect3>

<sect3><title>pppoe-relay</title>
<para><command>pppoe-relay</command> starts the server relay agent.</para></sect3>

<sect3><title>pppoe-server</title>
<para><command>pppoe-server</command> starts the server component.</para></sect3>

<sect3><title>pppoe-sniff</title>
<para>A small network sniffer designed to assist in setting <envar>PPPOE_EXTRA
</envar> settings.</para></sect3>

</sect2>

</sect1>