| 1 | <!DOCTYPE sect1 PUBLIC "-//OASIS//DTD DocBook XML V4.3//EN"
|
|---|
| 2 | "http://www.oasis-open.org/docbook/xml/4.3/docbookx.dtd" [
|
|---|
| 3 | <!ENTITY % general-entities SYSTEM "../../general.ent">
|
|---|
| 4 | %general-entities;
|
|---|
| 5 | ]>
|
|---|
| 6 |
|
|---|
| 7 | <sect1 id="kernel" xreflabel="kernel">
|
|---|
| 8 | <?dbhtml filename="kernel.html"?>
|
|---|
| 9 | <title>Configuring your kernel for CD-Writing</title>
|
|---|
| 10 |
|
|---|
| 11 | <para>In the kernel configuration, check your settings with those listed
|
|---|
| 12 | below for your <acronym>CD</acronym>-<acronym>ROM</acronym> interface type:</para>
|
|---|
| 13 |
|
|---|
| 14 | <para><acronym>SCSI</acronym> <acronym>CD</acronym>-writer:</para>
|
|---|
| 15 | <screen>SCSI support menu
|
|---|
| 16 | SCSI support: Y or M
|
|---|
| 17 | SCSI CD-ROM support: Y or M
|
|---|
| 18 | SCSI generic support: Y or M
|
|---|
| 19 | Vendor-specific extensions: [1]
|
|---|
| 20 | Also include the low-level driver for your SCSI card if
|
|---|
| 21 | applicable.</screen>
|
|---|
| 22 |
|
|---|
| 23 |
|
|---|
| 24 | <para><acronym>IDE</acronym> <acronym>CD</acronym>-writer:</para>
|
|---|
| 25 | <screen>ATA/IDE/MFM/RLL support menu
|
|---|
| 26 | IDE/ATAPI CDROM support: N
|
|---|
| 27 | SCSI emulation support: Y or M
|
|---|
| 28 | SCSI support menu
|
|---|
| 29 | SCSI support: Y or M
|
|---|
| 30 | SCSI CD-ROM support: Y or M
|
|---|
| 31 | SCSI generic support: Y or M
|
|---|
| 32 | Vendor-specific extensions: [1]</screen>
|
|---|
| 33 |
|
|---|
| 34 | <para>[1] Read the help to determine if this selection is applicable for
|
|---|
| 35 | your hardware.</para>
|
|---|
| 36 |
|
|---|
| 37 | <para>If necessary, recompile the kernel with</para>
|
|---|
| 38 | <screen>make CC=/opt/gcc-2.95.3/bin/gcc dep &&
|
|---|
| 39 | make CC=/opt/gcc-2.95.3/bin/gcc bzImage &&
|
|---|
| 40 | make CC=/opt/gcc-2.95.3/bin/gcc modules &&
|
|---|
| 41 | make CC=/opt/gcc-2.95.3/bin/gcc modules_install</screen>
|
|---|
| 42 | <para>
|
|---|
| 43 | Copy <filename>/usr/src/linux/arch/i386/boot/bzImage</filename> and
|
|---|
| 44 | <filename>/usr/src/linux/System.map</filename> to
|
|---|
| 45 | <filename>/boot</filename>. If you utilize
|
|---|
| 46 | <application>LILO</application>, edit <filename>/etc/lilo.conf</filename>
|
|---|
| 47 | appropriately and run <command>lilo</command>.
|
|---|
| 48 | </para>
|
|---|
| 49 |
|
|---|
| 50 | <para>For more information about these settings and the drivers they
|
|---|
| 51 | install, read <ulink
|
|---|
| 52 | url="http://www.tldp.org/HOWTO/SCSI-2.4-HOWTO/sr.html">The Linux 2.4
|
|---|
| 53 | SCSI subsystem HOWTO</ulink>.</para>
|
|---|
| 54 |
|
|---|
| 55 | </sect1>
|
|---|
| 56 |
|
|---|
