source: chapter05/fileutils-inst.xml@ bccc288

10.0 10.0-rc1 10.1 10.1-rc1 11.0 11.0-rc1 11.0-rc2 11.0-rc3 11.1 11.1-rc1 11.2 11.2-rc1 11.3 11.3-rc1 12.0 12.0-rc1 12.1 12.1-rc1 6.0 6.1 6.1.1 6.3 6.4 6.5 6.6 6.7 6.8 7.0 7.1 7.2 7.3 7.4 7.5 7.5-systemd 7.6 7.6-systemd 7.7 7.7-systemd 7.8 7.8-systemd 7.9 7.9-systemd 8.0 8.1 8.2 8.3 8.4 9.0 9.1 arm bdubbs/gcc13 ml-11.0 multilib renodr/libudev-from-systemd s6-init trunk v3_0 v3_1 v3_2 v3_3 v4_0 v4_1 v5_0 v5_1 v5_1_1 xry111/arm64 xry111/arm64-12.0 xry111/clfs-ng xry111/lfs-next xry111/loongarch xry111/loongarch-12.0 xry111/loongarch-12.1 xry111/mips64el xry111/pip3 xry111/rust-wip-20221008 xry111/update-glibc
Last change on this file since bccc288 was bccc288, checked in by Mark Hymers <markh@…>, 23 years ago

[Bug 140] Sed consistencies

git-svn-id: http://svn.linuxfromscratch.org/LFS/trunk/BOOK@1020 4aa44e1e-78dd-0310-a6d2-fbcd4c07a689

  • Property mode set to 100644
File size: 1.6 KB
Line 
1<sect2>
2<title>Installation of Fileutils</title>
3
4<para>The programs from a statically linked fileutils package may cause
5segmentation faults on certain systems. These systems are often, but not
6limited to, Linux systems that run Glibc-2.2.3 with an AMD CPU (Athlons
7and Durons are the most reported used CPU's). If you are in this category,
8run the following to sed commands before you compile this package.
9
10<screen><userinput>cp lib/Makefile.in lib/Makefile.in.backup &amp;&amp;</userinput>
11<userinput>sed 's/\(.*\)\(fopen-safer\.c \)\\/\1\2atexit.c \\/' \</userinput>
12<userinput>&nbsp;&nbsp;&nbsp;lib/Makefile.in &gt; tmp &amp;&amp;</userinput>
13<userinput>sed 's/\(.*\)\(idcache\$U\.\$.*\)\\/\1\2atexit$U.$(OBJEXT) \\/' \</userinput>
14<userinput>&nbsp;&nbsp;&nbsp;tmp &gt; lib/Makefile.in</userinput></screen></para>
15
16<para>Install fileutils by running the following commands:
17<screen><userinput>./configure --disable-nls \</userinput>
18<userinput>&nbsp;&nbsp;&nbsp;--prefix=$LFS/usr --libexecdir=$LFS/bin --bindir=$LFS/bin &amp;&amp;</userinput>
19<userinput>make LDFLAGS=-static &amp;&amp;</userinput>
20<userinput>make install &amp;&amp;</userinput>
21<userinput>cd $LFS/usr/bin &amp;&amp;</userinput>
22<userinput>ln -sf ../../bin/install</userinput></screen></para>
23
24<para>Once you have installed fileutils, you can test whether the
25segmentation fault problem has been avoided by running
26<userinput>$LFS/bin/ls</userinput>. If this works, then you are OK. If
27not, then you need to re-do the installation using the sed commands if
28you didn't use them, or without the sed commands if you did use
29them.</para>
30
31</sect2>
32
Note: See TracBrowser for help on using the repository browser.