%general-entities; ]> network configuring This section only applies if a network card is to be configured. Starting with version 209, systemd ships a network configuration daemon called systemd-networkd which can be used for basic network configuration. Additionally, since version 213, DNS name resolution can be handled by systemd-resolved in place of a static /etc/resolv.conf file. Both services are enabled by defualt, and absolutely should not be disabled. Configuration files for systemd-networkd (and systemd-resolved) can be placed in /usr/lib/systemd/network or /etc/systemd/network. Files in /etc/systemd/network have a higher priority than the ones in /usr/lib/systemd/network. There are three types of configuration files: .link, .netdev and .network files. For detailed descriptions and example contents of these configuration files, consult the systemd-link(5), systemd-netdev(5) and systemd-network(5) manual pages. Udev may assign network card interface names based on system physical characteristics such as enp2s1. If you are not sure what your interface name is, you can always run ip link after you have booted your system. The command below creates a basic configuration file for a Static IP setup (using both systemd-networkd and systemd-resolved): cat > /etc/systemd/network/10-eth0-static.network << "EOF" [Match] Name=eth0 [Network] Address=192.168.0.2/24 Gateway=192.168.0.1 DNS=192.168.0.1 EOF Multiple DNS entries can be added if you have more than one DNS server. The command below creates a basic configuration file for an IPv4 DHCP setup: cat > /etc/systemd/network/10-eth0-dhcp.network << "EOF" [Match] Name=eth0 [Network] DHCP=ipv4 EOF /etc/resolv.conf If the system is going to be connected to the Internet, it will need some means of Domain Name Service (DNS) name resolution to resolve Internet domain names to IP addresses, and vice versa. This is best achieved by placing the IP address of the DNS server, available from the ISP or network administrator, into /etc/resolv.conf. If using another means to configure your network interfaces (ex: ppp, network-manager, etc.), or if using any type of local resolver (ex: bind, dnsmasq, etc.), or any other software that generates an /etc/resolv.conf (ex: resolvconf), the systemd-resolved service should not be used. When using systemd-resolved for DNS configuration, it is responsible for creating the /etc/resolv.conf file. Since version 226, the symlink for /etc/resolv.conf is created by systemd when needed, so no further configuration is necessary. If a static /etc/resolv.conf is desired, create it by running the following command: cat > /etc/resolv.conf << "EOF" # Begin /etc/resolv.conf domain <Your Domain Name> nameserver <IP address of your primary nameserver> nameserver <IP address of your secondary nameserver> # End /etc/resolv.conf EOF The domain statement can be omitted or replaced with a search statement. See the man page for resolv.conf for more details. Replace <IP address of the nameserver> with the IP address of the DNS most appropriate for the setup. There will often be more than one entry (requirements demand secondary servers for fallback capability). If you only need or want one DNS server, remove the second nameserver line from the file. The IP address may also be a router on the local network. The Google Public IPv4 DNS addresses are 8.8.8.8 and 8.8.4.4 for IPv4, and 2001:4860:4860::8888 and 2001:4860:4860::8844 for IPv6. hostname configuring During the boot process, the file /etc/hostname is used for establishing the system's hostname. Create the /etc/hostname file and enter a hostname by running: echo "<lfs>" > /etc/hostname <lfs> needs to be replaced with the name given to the computer. Do not enter the Fully Qualified Domain Name (FQDN) here. That information is put in the /etc/hosts file. /etc/hosts localnet /etc/hosts network /etc/hosts Decide on the IP address, fully-qualified domain name (FQDN), and possible aliases for use in the /etc/hosts file. The syntax is: IP_address myhost.example.org aliases Unless the computer is to be visible to the Internet (i.e., there is a registered domain and a valid block of assigned IP addresses—most users do not have this), make sure that the IP address is in the private network IP address range. Valid ranges are: Private Network Address Range Normal Prefix 10.0.0.1 - 10.255.255.254 8 172.x.0.1 - 172.x.255.254 16 192.168.y.1 - 192.168.y.254 24 x can be any number in the range 16-31. y can be any number in the range 0-255. A valid private IP address could be 192.168.1.1. A valid FQDN for this IP could be lfs.example.org. Even if not using a network card, a valid FQDN is still required. This is necessary for certain programs to operate correctly. Create the /etc/hosts file by running: cat > /etc/hosts << "EOF" # Begin /etc/hosts (network card version) 127.0.0.1 localhost ::1 localhost <192.168.0.2> <HOSTNAME.example.org> [alias1] [alias2] ... # End /etc/hosts (network card version) EOF The <192.168.0.2> and <HOSTNAME.example.org> values need to be changed for specific uses or requirements (if assigned an IP address by a network/system administrator and the machine will be connected to an existing network). The optional alias name(s) can be omitted. If a network card is not going to be configured, create the /etc/hosts file by running: cat > /etc/hosts << "EOF" # Begin /etc/hosts (no network card version) 127.0.0.1 <HOSTNAME.example.org> <HOSTNAME> localhost ::1 localhost # End /etc/hosts (no network card version) EOF The ::1 entry is the IPv6 counterpart of 127.0.0.1 and represents the IPv6 loopback interface.