source: chapter07/network.xml@ 6aaa1b0

<?xml version="1.0" encoding="ISO-8859-1"?>
<!DOCTYPE sect1 PUBLIC "-//OASIS//DTD DocBook XML V4.3//EN" "http://www.oasis-open.org/docbook/xml/4.3/docbookx.dtd" [
  <!ENTITY % general-entities SYSTEM "../general.ent">
  %general-entities;
]>
<sect1 id="ch-scripts-network">
<title>Configuring the network script</title>
<?dbhtml filename="network.html"?>

<indexterm zone="ch-scripts-network">
<primary sortas="d-network">network</primary>
<secondary>configuring</secondary></indexterm>

<para>This section only applies if you're going to configure a network
card.</para>

<para>If you don't have any network cards, you are most likely not going to
create any configuration files relating to network cards. If that is the
case, you must remove the <filename class="symlink">network</filename> symlinks from all the
run-level directories
(<filename class="directory">/etc/rc.d/rc*.d</filename>)</para>

<sect2>
<title>Creating network interface configuration files</title>

<para>Which interfaces are brought up and down by the network script depends on
the files in the <filename class="directory">/etc/sysconfig/network-devices</filename> directory. This
directory should contain files in the form of <filename>ifconfig.xyz</filename>, where <quote>xyz</quote> is a
network interface name (such as eth0 or eth0:1)</para>

<para>If you decide to rename or move this <filename class="directory">/etc/sysconfig/network-devices</filename>
directory, make sure you update the <filename>/etc/sysconfig/rc</filename> file as well and
update the <quote>network_devices</quote> by providing it with the new path.</para>

<para>Now, new files are created in that directory.
The following command creates a sample <filename>ifconfig.eth0</filename> file:</para>

<screen><userinput>cat &gt; /etc/sysconfig/network-devices/ifconfig.eth0 &lt;&lt; "EOF"
ONBOOT=yes
SERVICE=ipv4-static
IP=192.168.1.1
GATEWAY=192.168.1.2
NETMASK=255.255.255.0
BROADCAST=192.168.1.255
EOF</userinput></screen>

<para>Of course, the values of those variables have to be changed 
in every file to match the proper setup. If the ONBOOT variable is set
to <quote>yes</quote>, the network script will bring up the equivalent NIC (Network Interface Card)
 during the booting of the system.
If set to anything but <quote>yes</quote>, the equivalent NIC will be ignored by the network script
and not brought up.</para>

<para>The SERVICE entry defines the method of obtaining the IP address.
The LFS bootscripts have a modular IP assignment format, and by creating
additional files in <filename class="directory">/etc/sysconfig/network-devices/services</filename>, you can allow
other IP assignment methods.  This would commonly be used if you need DHCP,
which is addressed in the BLFS book.</para>

<para>Of course, GATEWAY should contain the IP of your default gateway, if you
have one. If not, then comment out the variable entirely.</para>

</sect2>

<sect2 id="resolv.conf">
<title>Creating the /etc/resolv.conf file</title>
<indexterm zone="resolv.conf"><primary sortas="e-/etc/resolv.conf">/etc/resolv.conf</primary></indexterm>

<para>If you're going to be connected to the Internet then most likely you'll
need some means of DNS name resolution to resolve Internet domain names to IP
addresses. This is best achieved by placing the IP address of your DNS, available from your ISP (Internet Service Provider) or network administrator,
into <filename>/etc/resolv.conf</filename>. Create the file by running the
following:</para>

<screen><userinput>cat &gt; /etc/resolv.conf &lt;&lt; "EOF"
# Begin /etc/resolv.conf

domain {<replaceable>[Your Domain Name]</replaceable>}
nameserver <replaceable>[IP address of your nameserver]</replaceable>

# End /etc/resolv.conf
EOF</userinput></screen>

<para>Of course, replace <replaceable>[IP address of your nameserver]</replaceable> with the IP
address of the DNS most appropriate for your setup. There will often be
more than one entry (requirements demand secondary servers for fallback capability). The IP address may even be a router on your local network.</para>

</sect2>

</sect1>