%general-entities; ]> General Network Configuration network configuring This section only applies if a network card is to be configured. Network Interface Configuration Files Starting with version 209, systemd ships a network configuration daemon called systemd-networkd which can be used for basic network configuration. Additionally, since version 213, DNS name resolution can be handled by systemd-resolved in place of a static /etc/resolv.conf file. Both services are enabled by default. If you will not use systemd-networkd for network configuration (for example, when the system is not connected to network, or you want to use another utility like NetworkManager for network configuration), disable a service to prevent an error message during boot: systemctl disable systemd-networkd-wait-online Configuration files for systemd-networkd (and systemd-resolved) can be placed in /usr/lib/systemd/network or /etc/systemd/network. Files in /etc/systemd/network have a higher priority than the ones in /usr/lib/systemd/network. There are three types of configuration files: .link, .netdev and .network files. For detailed descriptions and example contents of these configuration files, consult the systemd-link(5), systemd-netdev(5) and systemd-network(5) manual pages. Network Device Naming Udev normally assigns network card interface names based on physical system characteristics such as enp2s1. If you are not sure what your interface name is, you can always run ip link after you have booted your system. The interface names depend on the implementation and configuration of the udev daemon running on the system. The udev daemon for LFS (systemd-udevd, installed in ) will not run unless the LFS system is booted. So it's unreliable to determine the interface names being used in LFS system by running those commands on the host distro, even though you are in the chroot environment. For most systems, there is only one network interface for each type of connection. For example, the classic interface name for a wired connection is eth0. A wireless connection will usually have the name wifi0 or wlan0. If you prefer to use the classic or customized network interface names, there are three alternative ways to do that: Mask udev's .link file for the default policy: ln -s /dev/null /etc/systemd/network/99-default.link Create a manual naming scheme, for example by naming the interfaces something like "internet0", "dmz0", or "lan0". To do that, create .link files in /etc/systemd/network/ that select an explicit name or a better naming scheme for your network interfaces. For example: cat > /etc/systemd/network/10-ether0.link << "EOF" [Match] # Change the MAC address as appropriate for your network device MACAddress=12:34:45:78:90:AB [Link] Name=ether0 EOF See the man page systemd.link(5) for more information. In /boot/grub/grub.cfg, pass the option net.ifnames=0 on the kernel command line. Static IP Configuration The command below creates a basic configuration file for a Static IP setup (using both systemd-networkd and systemd-resolved): cat > /etc/systemd/network/10-eth-static.network << "EOF" [Match] Name=<network-device-name> [Network] Address=192.168.0.2/24 Gateway=192.168.0.1 DNS=192.168.0.1 Domains=<Your Domain Name> EOF Multiple DNS entries can be added if you have more than one DNS server. Do not include DNS or Domains entries if you intend to use a static /etc/resolv.conf file. DHCP Configuration The command below creates a basic configuration file for an IPv4 DHCP setup: cat > /etc/systemd/network/10-eth-dhcp.network << "EOF" [Match] Name=<network-device-name> [Network] DHCP=ipv4 [DHCPv4] UseDomains=true EOF Creating the /etc/resolv.conf File /etc/resolv.conf If the system is going to be connected to the Internet, it will need some means of Domain Name Service (DNS) name resolution to resolve Internet domain names to IP addresses, and vice versa. This is best achieved by placing the IP address of the DNS server, available from the ISP or network administrator, into /etc/resolv.conf. systemd-resolved Configuration If using methods incompatible with systemd-resolved to configure your network interfaces (ex: ppp, etc.), or if using any type of local resolver (ex: bind, dnsmasq, unbound, etc.), or any other software that generates an /etc/resolv.conf (ex: a resolvconf program other than the one provided by systemd), the systemd-resolved service should not be used. To disable systemd-resolved, issue the following command: systemctl disable systemd-resolved When using systemd-resolved for DNS configuration, it creates the file /run/systemd/resolve/stub-resolv.conf. And, if /etc/resolv.conf does not exist, it will be created by systemd-resolved as a symlink to /run/systemd/resolve/stub-resolv.conf. So it's unnecessary to create a /etc/resolv.conf manually. Static resolv.conf Configuration If a static /etc/resolv.conf is desired, create it by running the following command: cat > /etc/resolv.conf << "EOF" # Begin /etc/resolv.conf domain <Your Domain Name> nameserver <IP address of your primary nameserver> nameserver <IP address of your secondary nameserver> # End /etc/resolv.conf EOF The domain statement can be omitted or replaced with a search statement. See the man page for resolv.conf for more details. Replace <IP address of the nameserver> with the IP address of the DNS server most appropriate for your setup. There will often be more than one entry (requirements demand secondary servers for fallback capability). If you only need or want one DNS server, remove the second nameserver line from the file. The IP address may also be a router on the local network. Another option is to use the Google Public DNS service using the IP addresses below as nameservers. The Google Public IPv4 DNS addresses are 8.8.8.8 and 8.8.4.4 for IPv4, and 2001:4860:4860::8888 and 2001:4860:4860::8844 for IPv6. Configuring the system hostname hostname configuring During the boot process, the file /etc/hostname is used for establishing the system's hostname. Create the /etc/hostname file and enter a hostname by running: echo "<lfs>" > /etc/hostname <lfs> needs to be replaced with the name given to the computer. Do not enter the Fully Qualified Domain Name (FQDN) here. That information is put in the /etc/hosts file. Customizing the /etc/hosts File /etc/hosts localnet /etc/hosts network /etc/hosts Decide on a fully-qualified domain name (FQDN), and possible aliases for use in the /etc/hosts file. If using static IP addresses, you'll also need to decide on an IP address. The syntax for a hosts file entry is: IP_address myhost.example.org aliases Unless the computer is to be visible to the Internet (i.e., there is a registered domain and a valid block of assigned IP addresses—most users do not have this), make sure that the IP address is in the private network IP address range. Valid ranges are: Private Network Address Range Normal Prefix 10.0.0.1 - 10.255.255.254 8 172.x.0.1 - 172.x.255.254 16 192.168.y.1 - 192.168.y.254 24 x can be any number in the range 16-31. y can be any number in the range 0-255. A valid private IP address could be 192.168.1.1. If the computer is to be visible to the Internet, a valid FQDN can be the domain name itself, or a string resulted by concatenating a prefix (often the hostname) and the domain name with a . character. And, you need to contact the domain provider to resolve the FQDN to your public IP address. Even if the computer is not visible to the Internet, a FQDN is still needed for certain programs, such as MTAs, to operate properly. A special FQDN, localhost.localdomain, can be used for this purpose. Create the /etc/hosts file using the following command: cat > /etc/hosts << "EOF" # Begin /etc/hosts <192.168.0.2> <FQDN> [alias1] [alias2] ... ::1 ip6-localhost ip6-loopback ff02::1 ip6-allnodes ff02::2 ip6-allrouters # End /etc/hosts EOF The <192.168.0.2> and <FQDN> values need to be changed for specific uses or requirements (if assigned an IP address by a network/system administrator and the machine will be connected to an existing network). The optional alias name(s) can be omitted, and the <192.168.0.2> line can be omitted if you are using a connection configured with DHCP or IPv6 Autoconfiguration, or using localhost.localdomain as the FQDN. The /etc/hostname does not contain entries for localhost, localhost.localdomain, or the hostname (without a domain) because they are handled by the myhostname NSS module, read the man page nss-myhostname(8) for details. The ::1 entry is the IPv6 counterpart of 127.0.0.1 and represents the IPv6 loopback interface.